Expert Concrete Coating Removal In Minnesota
Clean, Profiled Concrete Before Any New Floor Goes Down
Every good commercial floor starts with a clean, profiled slab. Concrete coating removal is the step that makes that possible, and it is the step most contractors rush. Roll new epoxy over an old peeling coat and it peels again. Thinset left behind shows through an overlay, and glue residue kills the bond. Every time.
The Concrete Guy removes old flooring, coatings, and adhesives with industrial equipment and full dust control. Then our grinders cut the concrete to the exact profile the new system needs. That one step decides how long the next floor lasts. Property managers and general contractors deal with one crew that owns the demo, the prep, and the finished floor.
Flooring And Coatings We Remove From Commercial Slabs
Our crews remove failed epoxy and urethane coatings, paint, sealers, and curing compounds. We take out ceramic and porcelain tile, VCT, sheet vinyl, carpet, and wood. The thinset, mastic, cutback adhesive, and glue left behind come out too, along with rubber flooring and old overlays.
Each material needs its own approach, and the wrong tool can gouge the slab or leave a film that the new floor will not stick to. Thick coatings come off with shot blasting or coarse diamond tooling. Tile breaks out with machines, and the thinset gets ground flat. Soft adhesives need scraping or special tooling that keeps them from gumming up the diamonds.
We test black cutback adhesive before removal because older material can contain asbestos. When it does, a licensed abatement partner handles it first. Haul-away and disposal of everything we remove are part of the contract. No extra bill.
One Contractor From Demolition To The Finished Floor
Hiring a demo crew and a flooring contractor separately leaves a gap. If the new floor fails, each one blames the other. We own the whole scope and warrant a finish we built on our own prep.
Shot blasters, planetary grinders, scarifiers, and ride-on scrapers come to every commercial job. Equipment sized for warehouses turns a storefront or clinic into a quick project.
When the slab under old tile is worse than expected, we document it with photos, explain the repair options, and price them before we continue. You never get surprise change orders.
What Proper Coating Removal Delivers
A new floor that bonds to bare concrete
No old coating hiding moisture problems
Flat slabs with no thinset ridges
Adhesive residue gone from every corner
The right surface profile for the next system
HEPA dust control in occupied buildings
Cracks and spalls repaired during prep
Photo records of the prepared slab
Demo and finish under one warranty
Haul-away and disposal included
Night and weekend work available
Moisture testing on the bare slab

Concrete Coating Removal Without Shutting Down The Building
The Concrete Guy does most removal work inside buildings that stay open. Retail stores, clinics, warehouses, and restaurants cannot close for a week. We split the floor into sections, work nights and weekends, and coordinate with your team on access and noise.
Grinding without containment covers a building in silica dust. We run HEPA-filtered vacuums on every grinder and seal off the work zone where nearby rooms stay occupied. When removal is part of a larger project, we schedule prep and the new floor together, so your space goes out of service once instead of twice.
What Contractors And Property Managers Say About Us





Removal Projects We Handle Every Month

Failed Epoxy And Paint
Peeling box-store epoxy and old floor paint come off with shot blasting or coarse diamonds. The slab is then ready for a properly built commercial system.

Tile, Thinset, And Grout
We break out ceramic, porcelain, and quarry tile, then grind thinset flat. Kitchens and restrooms move to joint-free floors with no grout to clean. Restrooms get the same treatment.

VCT, Vinyl, And Mastic
Many grocery stores and offices sit on layers of VCT and black mastic. Ride-on scrapers lift the tile, and grinders remove the glue below. Polishing or coating can follow right away.

Carpet And Carpet Glue
Office and school conversions start with carpet removal. We strip the pad, grind off the glue, and leave a slab ready for polishing or coating.

Sealers And Curing Compounds
Clear sealers block stain, dye, and coatings from soaking in. We grind them off so color and resin can reach the concrete. A quick water drop test tells us where sealer remains.

Worn Overlays And Old Patches
Delaminated toppings and failed patch work come out down to sound concrete. Then we resurface with a system that bonds. Hollow spots get found by sounding the slab before we start.
Concrete Grinding And Surface Preparation
Removal is half the job. Grinding is the other half. The slab gets a surface profile matched to the finish. Thin coatings need a light profile. High-build epoxy, urethane cement, and overlays need a deep, rough one. We test moisture after prep so the readings reflect the bare slab.

How We Plan A Coating Removal Job
The job starts with a site walk. We identify each material on the floor, test suspect adhesives, and check the slab underneath where we can. Then we choose tooling for each area and write a schedule that fits your hours.
During removal, our crews work in sections with HEPA vacuums running. Thick coatings, tile, and glue come off first. Grinding follows, then crack and joint repair, then a full clean of the slab. Each section gets checked before we move on.
We document the prepared slab with photos and profile notes. General contractors and property managers get a record of the surface the new floor went down on. A 5,000 square foot retail floor with VCT and glue usually takes two to three days to remove and prepare.
Recent Removal, Grinding, And Finish Projects
Concrete Coating Removal FAQs
How do you remove a failed epoxy floor?
Thick, well-bonded epoxy comes off with a shot blaster or a planetary grinder fitted with coarse diamond tooling. Scrapers take the peeling sections first. Then the grinder removes the remaining film and profiles the slab for the next system. HEPA vacuums control dust the whole time.
Can you remove tile and thinset without damaging the slab?
Yes. We break out the tile with machines and grind the thinset flat with diamond tooling chosen for the hardness of the mortar. Any minor gouges get patching compound before the finish system goes down, so the new floor sits flat.
How long does coating removal take?
A 5,000 square foot retail floor with VCT and adhesive takes about two to three days to remove and prepare. Tile and thick coatings take longer. You get a firm schedule after the site walk. We phase larger floors so the business can keep selling, serving, or shipping while we work through one section at a time.
What happens to the old flooring we remove?
Haul-away and disposal of the removed flooring, coatings, and debris are part of our contract. If any material tests positive for asbestos, a licensed abatement partner handles it before our work begins, and we wait for their clearance before a single grinder starts up.
Do you remove failed coatings from garages too?
Yes. Failed box-store epoxy kits bring plenty of Twin Cities homeowners to us. We grind off the old coating and install a new garage floor system with a lifetime adhesion warranty.
Concrete Knowledge Behind Every Grinder We Run
I am Matt Hage, owner of The Concrete Guy. My family has worked Minnesota concrete since 1920. That background teaches you to read a slab before the first pass. Soft concrete, lightweight mixes, and gypsum underlayments each need their own plan. We handle removal across the metro. That includes Minneapolis, Edina, Prior Lake, Savage, and Apple Valley. We also travel for projects nationwide.
Pair removal with concrete resurfacing or polished concrete, or request a removal quote today.









